How to Huawei TWRP Recovery Unlock Bootloader

How to Unlock Bootloader and Install TWRP on the Huawei MediaPad T3 10

Her I am going to tell you about the way to “Unlock Bootloader, Install TWRP- the Huawei MediaPad T3 10”. Huawei MediaPad T3 10 is not a popular device and also not a bad device. This tablet was launched in October 2017 with the resolution of 1280×800. The tablets are not best-selling devices. It takes about months to find the way to unlock the device and install TWRP on it. 

The size, and weight of the product. Its related specifications are theoretical values only. Measurements between individual and products may change. All specifications are related to the actual product.


How to Unlock Bootloader and Install TWRP on the Huawei MediaPad T3 10

Specs of Huawei MediaPad T3 10:-


Space Gray                     Luxurious Gold


          Size: 9.6 inches

          Type: IPS display

          Resolution: 1280 × 800 (HD)

          Pixel density: 157 PPI

          Contrast: 800:1

          Brightness: 300 nits (typical)

  • CPU:

Qualcomm MSM8917, quad-core A53


Android™ N (Nougat)


          ROM: 16 GB RAM: 2 GB*        or       ROM: 32 GB RAM: 3 GB*

Because of some limitations in CPU processing power, and memory (used by the operating system and pre-installed applications) the space available to users will be low.


          WIFI/WAPI: 802.11 a/b/g/n@2.4GHz&5GHz

  • GPS:

Supports GPS, A-GPS, GLONASS, and BDS.


        LTE-FDD: B1, B3, B5, (B19), B7, B8, B20

        LTE-TDD: B38, B39, B40, B41 (2555–2655MHz)

        UMTS: B1, B2, B5 (B6/19), B8

        TD-SCDMA: B34, B39

        GSM: B2, B3, B5, B8

        WIFI/WAPI: 802.11 a/b/g/n@2.4GHz&5GHz


Gravity sensor


Rear camera: 5 MP and autofocus

 Front camera: 2 MP and fixed focus


4800 mAh*

Note: The real battery capacity for each individual product may be above or below the nominal battery capacity.


Products that earn the ENERGY STAR® prevent greenhouse gas emissions. It is done by strict meeting on energy efficiency requirements set by the U.S. Environmental Protection Agency.

Accessories within the box:-

  • Charger x 1
  • Cable x 1
  • Eject tool x 1
  • Quick Start Guide x 1
  • Warranty Card x 1

Note: specifications may change without notice. Colour may change.


  1. Install ADB and Fastboot on your computer.
  2. Make sure you have the latest Huawei USB Drivers installed on your PC.
  3. Your MediaPad has battery above than 50%.
  4. Enable USB debugging and OEM unlocks on your MediaPad T3 10.
  5. Download TWRP 3.1.1 for Huawei-MediaPad T3 10

Steps to Unlock Bootloader on Huawei MediaPad T3 10:-

You can usually get an unlock code from the manufacturer.

  • When you have the code, launch the ADB command interface. Linux and Mac users can simply use a Terminal window and it’ll work. Windows users can do this by navigating to the ABD installation folder. Once there, type cmd in the address bar and hit enter.
  • Connect your phone to PC in fastboot mode. Power off your device first. Then press and hold the Volume down button. While connecting your phone to the PC, you can just connect your device in MTP mode. While its powered on, and use the following command to reboot it into fastboot mode.
  • Replace your unlock code with the unlock code that you’ve received.

Steps to Install TWRP on Huawei MediaPad T3 10:-

Your device’s bootloader is unlocked you can install any custom recovery such as TWRP.

  • Download the TWRP recovery image from above link. Rename the file. Give it a simple name such as img. Move it to the adb installation directory.
  • If your phone is disconnected, connect it again in fastboot mode.
  • In the adb window, type the following command and hit enter to flash the recovery image to your device.

“fastboot flash recovery twrp.img”

  • When the flashing is complete, disconnect your phone and reboot.

Leave a Comment